+86-510-83380342

How to maintain the Hollow Shaft Cooling Conveyor

Apr 30, 2025

The maintenance of the long-life hollow shaft cooling conveyor (Hollow Shaft Cooling Conveyor) needs to focus on structural sealing, medium circulation system, transmission components, material compatibility and environmental adaptability. The life cycle of the equipment can be extended through systematic maintenance. The specific requirements are as follows:

1. Cooling system sealing maintenance

Regular leak detection: Check the hollow shaft interface, pipe welds and valve connections every week, use soapy water or a halogen detector to check for coolant leaks, and pay special attention to the sealing parts of the shaft and the bearing seat (the protection level must be maintained above IP65). If leakage is found, replace the aging O-ring or repair the weld in time to avoid medium loss and reduced cooling efficiency.

Medium quality management: Replace the cooling medium (such as coolant) every quarter, and remove impurities and scale in the pipeline. Use deionized water or special anti-rust coolant to prevent corrosion and scaling of the inner wall of the shaft. Regularly test the pH value and conductivity of the medium to ensure that it is in the neutral range (pH=6.5-7.5) to avoid acidic or alkaline media that accelerate metal corrosion.

2. Transmission and bearing system maintenance

Bearing lubrication: Add high-temperature lithium-based grease to the support bearings and transmission bearings every month, using the principle of "small amounts and multiple times" to avoid grease accumulation and heating. For high-speed precision bearings, it is recommended to perform ultrasonic cleaning every six months to detect the degree of wear. If the clearance exceeds 0.05mm, it needs to be replaced in time.

Transmission parts inspection: Check the tension of gears, chains or synchronous belts weekly and adjust them to the standard value specified by the manufacturer (such as the chain sag is controlled at 20-30mm). If the gear tooth surface is worn more than 1/3 and the chain elongation exceeds 3%, it needs to be replaced immediately to prevent eccentric wear of the shaft due to unstable transmission.

info-380-380

3. Maintenance of structure and material durability

Anti-corrosion treatment: Check the anti-corrosion coating on the surface of the hollow shaft every year. If the chrome plating or epoxy resin coating is damaged, it needs to be repainted in time. For stainless steel shafts, non-abrasive cleaners can be used to remove surface rust, and sharp tools such as steel wool should be avoided to damage the passivation film.

Deformation monitoring: The straightness of the shaft is tested by a laser distance meter every quarter, and the allowable deviation is ≤0.1mm/m. If the shaft is found to be bent or the bearing seat is offset, it needs to be reset by hydraulic correction equipment to avoid structural cracking due to stress concentration.

4. Intelligent monitoring and preventive maintenance

Operation data recording: Check the temperature, pressure, and flow curves of the equipment control system every day and compare them with historical data. If the temperature difference between the inlet and outlet of the cooling medium suddenly decreases (such as the normal temperature difference of 5°C drops to 2°C), it may indicate blockage in the shaft or a decrease in heat exchange efficiency, and the machine must be shut down immediately for inspection.

Replacement cycle of wearing parts: Establish maintenance records to record the life of key parts (such as 2 years for seals, 6 months for filters, and 5 years for hoses), and replace them before expiration. For example, rubber seals are prone to aging due to long-term contact with coolant. It is recommended to replace them uniformly every 18 months to avoid sudden leakage affecting production.

5. Environmental adaptability adjustment

In dusty or humid environments, maintenance frequency needs to be increased:

Dust environment: Use compressed air to blow away dust on the bottom of the conveyor belt and the surface of the shaft every week to prevent dust from entering the bearing gap and aggravating wear;

Humid environment: Check the insulation resistance of the electrical system every month (needs to be ≥2MΩ), and take dehumidification measures for the control cabinet (such as installing a semiconductor dehumidifier) to avoid circuit short circuits.

If you need high quality Hollow Shaft Cooling Conveyor , please contact Changrong for more questions.

 

 

Send Inquiry